Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterTrusted Gate Parts & Welding for Beverly Hills Homeowners
A gate that drags, sags, or won’t latch is more than a nuisance in Beverly Hills. It’s the first thing a visitor sees, and a gate that doesn’t close properly leaves a home open. For over two decades, Hal Gatewood and the crew at Gatewood Fence & Gate have repaired gate hardware and welded broken frames on site, right in the driveway, so homeowners never have to haul a 400-pound gate across town. We answer the phone 24 hours a day at (559) 844-6989, and when you call, a live person picks up. Not a phone tree. Not a chatbot. Hal’s name is on the shop, and his address is published, which means when we say we’ll be there at 2:00, that’s when you’ll see the truck. A gate sags in the hinge post, not in the middle, and that’s where we start.
We’ve been serving homeowners in Beverly Hills since 2001, and in that time, we’ve learned something about gate parts and welding that most companies never figure out: repair usually beats replacement. A cracked weld, a worn hinge, a bent rail. These are fixable. You don’t need a new gate when a few hours of on-site welding and the right parts will make the old one outlast whatever the big-box store is selling. Every job we do carries the 90-Day Done Right Promise in writing. If it’s not done right, we make it right. One call brings Hal back. No runaround.
What Our Gate Parts & Welding Service Includes
Most gate failures boil down to a handful of parts that bear the entire weight of a moving gate day after day. Here at Gate Parts & Welding in Beverly Hills, we fix all of them. Below are the specific services we provide, how to know you need them, and what our approach looks like.
Hinge Replacement
Hinges take more beating than any other component on a gate. Every open and close cycle pivots the entire panel on two or three hinge points, and when those wear out, the gate drops. At our Gate Parts & Welding in Beverly Hills, where many homes have heavy ornamental iron gates, we routinely see hinge pins worn down to half their original diameter. We carry heavy-duty ball-bearing hinges and weld-on barrel hinges, and we replace them on site. The gate never leaves your property. A new hinge that’s oversized for the weight of the gate is the difference between a five-year fix and a two-year patch.
Post Replacement
The hinge post holds the gate. If the post is leaning, cracked, or rusted at the base, no amount of hinge adjustment will fix the problem. A gate sags in the hinge post, not in the middle, and that is where we start. We set new steel posts in concrete, braced and plumbed, and we won’t hang the gate back up until the post is dead level. In Beverly Hills, where soil moisture and older concrete footings can undermine a post, we dig the old footing out and pour fresh concrete with proper drainage so water can’t pool at the base. Fix the panel without the post and you’ll fix it twice.
Rail Repair
The top and bottom rails give a gate its shape and carry the pickets or infill. When a rail rusts through or bends, the gate starts to wobble, and if a bottom rail breaks, the entire panel can twist and bind against the ground. We cut out the damaged section, weld in a new piece of matching steel, and grind the joint smooth so the repair disappears under paint. If you’re in Beverly Hills and your gate scrapes the driveway on one corner, it’s likely a bottom rail that cracked. Don’t wait for it to snap completely, because a snapped rail will tear the pickets off with it.
Custom Welding
Sometimes the part a gate needs isn’t sold anywhere. A decorative scroll that cracked in two, a custom bracket that failed, a mounting plate that needs to be thicker than anything at the supply house. We do custom welding on site, and we build parts that match the existing steel. Hal has been welding since 2001, and his welds aren’t the spattered bird-droppings mess you see on some gates. They’re clean, penetrating, and ground smooth. For Beverly Hills homes with older custom gates, this is often the only way to avoid replacing a one-of-a-kind piece with a generic panel from a catalog.
Gate Rollers
Sliding gates run on rollers. Cantilever gates have rollers inside the frame, and V-track gates ride on roller assemblies bolted to a concrete pad. When rollers seize up, the gate fights you the whole way, and the motor works twice as hard until it burns out. We replace worn rollers with sealed-bearing units that don’t need greasing every three months. A sliding gate in Beverly Hills should roll with one hand. If it takes two hands and a shoulder, those rollers are done. Replacing them before they grind flat saves the track, the motor, and eventually the gate frame itself.
Latch & Lock
A latch that doesn’t catch is a gate that doesn’t do its job. Swing gates especially depend on a solid latch to keep the panel closed against wind and wandering hands. We install and align drop-rod latches, magnetic catches, keyed locks, and electric strikes for automated gates. If you have to lift the gate to get the latch to engage, the geometry is off, and every day it goes unfixed, the hinges and the post are paying for it. A properly adjusted latch closes with a click, not a struggle.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Gate Parts & Welding
BFT gate operators are common in Beverly Hills estates, and we have serviced hundreds of them over the years. These operators are built to move heavy gates, but when the mechanical parts wear out, the control board takes the blame. We stock BFT OEM parts and know the quirks of these units well enough to diagnose a problem over the phone before we even arrive. If the issue is mechanical, we fix the mechanics. If the board is failing, we tell you straight and give you a price before any work starts.
Linear operators are another staple in this neighborhood. The company makes a wide range of swing and slide operators, and we keep their armatures, limit switches, and capacitor kits on the truck. Viking and Ghost Controls round out the brands we see most often on residential properties. Ghost Controls units are popular DIY-friendly kits, and we’re the crew called in when those installations go sideways. If the gate is binding, the problem isn’t the opener. Show me the gate closing on its own and I’ll show you where it’s failing. Whether you have one of these brands or any other make, we can help. We’re certified to service nine major brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule.
Signs You Need Gate Parts & Welding Right Now
- Your gate drags or scrapes the ground. A gate that scrapes the driveway is telling you a hinge is worn, a post has shifted, or a rail is cracked. Every scrape grinds metal away, and the damage compounds fast. In Beverly Hills, where driveway slopes are common, this is the top warning sign we see.
- The gate leans noticeably to one side. A lean means the hinge post is moving or the hinges themselves have worn out of round. A gate that leans is hanging its entire weight on one tired hinge. The longer you wait, the more likely you’ll need a post replacement instead of a hinge replacement.
- Opening and closing takes real effort. A properly hung and balanced gate moves easily. If you’re putting your shoulder into it, something is binding, and that resistance is being felt by every bolt, hinge, and weld in the system. A little strain today becomes a cracked weld tomorrow.
- You can see rust bleeding through the paint. Rust on the surface means moisture has been working on the steel for months. By the time you can see it, the metal underneath is thinner than it was built. On welded joints, rust at the seam is the first sign a weld is weakening and may be close to separating.
- The latch won’t stay engaged without lifting the gate. If you have to heave the gate upward to get the latch to line up, the geometry has shifted. That shift is never the latch’s fault. It’s the post, the hinges, or a sagging rail. Aligning a latch on a sagging gate is like straightening a picture on a crumbling wall.
Our Gate Parts & Welding Process - Step by Step
We follow the same process on every gate job, whether it’s a simple hinge replacement in the flats or a full post rebuild up in the hills. There are no surprises, and the price is agreed to before we touch a single weld.
- 1
You call, a live person answers. Day or night, you’ll get a real person on the line at (559) 844-6989. We’ll ask what the gate is doing, what kind of gate it is, and whether it’s manual or automated. Often, we can give you a rough idea of what we’re dealing with before we even schedule the visit.
- 2
Hal shows up and looks at the whole gate. We don’t just look at the part that’s broken. We look at the post that holds it, the hinges that carry it, the track it rolls on, and the way the panel sits in the opening. A broken part is a symptom. The gate is the patient. Takes about 30 to 45 minutes to go over everything.
- 3
You get an upfront price. Before any work starts, you get a written price for parts and labor. No trip charge inside the county. No haggling. We honor the standing offers: $40 off any repair over $200, a free second opinion on any written estimate, and a permanent 10% discount for seniors and veterans. You approve the price before we pull out a wrench.
- 4
We fix it on site. Hal or one of his crew welds, grinds, aligns, and test-cycles the gate right in your driveway. The gate stays on your property the entire time. We carry a mobile welding rig and enough parts on the truck to handle most hinge, roller, latch, and rail jobs in a single visit.
- 5
You test it, and we write the promise. Before we leave, you operate the gate yourself. You run it open and closed, listen to it, feel it. Then we hand you the 90-Day Done Right Promise in writing. If anything isn’t right in the next 90 days, one call brings us back. No fine print. No prorating. That’s the whole deal.
How Much Does Gate Parts & Welding Cost in Beverly Hills?
Here’s how much Gate Parts & Welding costs in Beverly Hills: typically $180 to $340 for a hinge replacement, $340 to $680 for a post replacement, and $150 to $380 for a basic weld repair depending on the size of the crack and the access to the work area. Here’s a breakdown of what we see most often:
- Hinge replacement: $180-$340 per hinge, depending on size and type
- Post replacement: $340-$680 per post, including concrete and steel
- Rail repair or replacement: $120-$280 per rail section
- Custom welding (cracks, brackets, broken pickets): $150-$380 per repair
- Gate roller replacement: $160-$350 per roller assembly
- Latch and lock replacement or realignment: $120-$260
A few things move the price. A gate that’s located on a steep slope with poor truck access takes longer to work on. A post that’s set in an oversized footing takes longer to dig out. A gate that needs multiple components addressed in one visit will be more efficient per repair than scheduling them separately. We quote everything before we start, and that quote is the price. If we find something unexpected when we open the gate up, we stop and show you before we spend another dollar. You’ll never get a bill bigger than the number you approved.
Gate Parts & Welding Near Beverly Hills - Our Service Area
We’re based close enough to reach most of Beverly Hills within 30 to 45 minutes, and we regularly serve homes in Sherman Oaks, West Hollywood, Van Nuys, Tarzana, North Hollywood, Encino, Reseda, Studio City, and Brentwood. Same response time applies across the county. Our work in Los Angeles and Santa Monica covers the same range of hinge, post, rail, roller, and latch repairs with the same on-site welding rig. No trip charge inside the county, which means the estimate you get is what you’d pay if the shop were across the street.
Serving Beverly Hills, CA - Our Local Coverage Area
We’re based in the Beverly Hills area and know this community well, and we also provide Studio City Gate Parts & Welding. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Gate Parts & Welding in Beverly Hills
Gate parts and welding covers the repair and replacement of the mechanical and structural components that make a gate function: hinges, posts, rails, rollers, latches, and locks. Welding is used to repair cracked steel, replace broken sections, and install new parts that bolt to the gate frame. At Gatewood Fence & Gate, we do all of this on site in Beverly Hills, so the gate never leaves your driveway. We also offer Gate Parts & Welding - West Hollywood.
Most hinge, latch, and roller replacements are completed in 90 minutes to 3 hours. A post replacement, which involves digging out the old footing and pouring fresh concrete, takes a full day including cure time. Welding repairs depend on the extent of the damage, but a typical cracked rail or broken picket is done in under an hour per repair. We’ll give you a time estimate before we start, and we stick to it.
Most gate parts and welding repairs in Beverly Hills run between $120 and $680 depending on the component. A simple latch realignment is on the lower end, while a full post replacement with new steel and concrete is at the top. We give you the full price before any work begins, and we honor the standing $40-off-any-repair-over-$200 offer plus a 10% discount for seniors and veterans. Call (559) 844-6989 for an exact quote, and estimates are free.
Yes. We service BFT and Linear gate operators extensively in Beverly Hills, along with Viking, Ghost Controls, DoorKing, Elite, LiftMaster, FAAC, and Mighty Mule. We stock OEM parts for the most common models and can diagnose most operator faults within the first visit. If the issue is a mechanical failure at the gate rather than the operator, we’ll tell you that plainly and fix the real problem instead of swapping out a board that didn’t need to go.
Yes. A live person answers our phone 24 hours a day, 7 days a week, and we keep same-day availability for emergency gate repairs in Beverly Hills and the surrounding county. If your gate has failed in a position that leaves your property unsecured or your cars trapped, call (559) 844-6989 and we’ll prioritize getting to you. There’s no trip charge inside the county, and we’ll tell you over the phone whether we can get you on the schedule today.
Every gate parts and welding job we do carries the 90-Day Done Right Promise in writing. If a weld cracks, a hinge loosens, or a part we installed fails within 90 days, one call brings Hal or his crew back to make it right. No prorating, no arguing, no “we need to inspect it first with a service fee.” We stand behind the work because we do the work ourselves.
Make sure we can access the gate from both sides if possible, and move any cars or yard equipment that block the work area. If the gate is automated, leave the operator powered on unless it’s actively smoking or sparking. You don’t need to remove anything from the gate or take anything apart. We show up with the tools, the welder, and the parts, and we’ll tell you if we need anything else after we’ve had a look.
Schedule Your Gate Parts & Welding Service in Beverly Hills Today
If your gate is dragging, leaning, or refusing to latch, don’t wait for a small repair to become a full replacement. Call Gatewood Fence & Gate at (559) 844-6989 and talk to a live person. We’ll give you a free estimate, an honest assessment, and a price you can hold us to. Hal Gatewood has been fixing gates in Beverly Hills since 2001, and the name is on the shop.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Beverly Hills since 2001.