Linear Access Control Installation Nationwide | Gatewood Fence & Gate

Linear Access Control Installation: The Beverly Hills Owner’s Guide

We stock and install Linear-compatible access control parts across Beverly Hills, with most installations running $240 to $580 depending on the part and your gate’s wiring. If your keypad went dark, your receiver stopped hearing the remote, or the gate ignores the entry command from the house, you’ve already found the failure, now you need the right replacement matched to your Linear model and installed so it doesn’t fail the same way twice. The giveaway is usually specific: a Linear keypad that blinks but won’t transmit, an operator that runs when you hit the test button but not when a vehicle pulls up, or a receiver that worked fine for six years and now won’t respond from more than ten feet away.

Call (559) 844-6989

Here’s what we know from opening up Linear systems in Beverly Hills driveways for over two decades: Linear parts fail predictably, and the fix is usually one component, not a whole new system. The challenge is matching the part to the model year, because Linear made good hardware but they didn’t make it universal, and a 2012 receiver won’t always talk to a 2021 keypad without knowing exactly which generation you’re holding. That’s the whole job right there, and it’s why we show up with the right part the first time instead of guessing from a catalog photo.

Which Linear Models This Applies To

The parts we install cover the Linear series owners actually have in this area: the Multi-Code receivers and transmitters, Delta-3 radio controls, the AM-KP and AE-KP keypads, and the APT and LRA line of gate operators. If your operator says Linear Pro Access, Linear AccessBase, or you’ve got an AK-11 keypad from the mid-2000s mounted by the driveway, that’s in our wheelhouse. The compatibility gotcha with Linear is frequency: older Multi-Code gear runs on 300 MHz, while newer Linear access controls shifted to 318 MHz, and a remote that works on one will not work on the other, no matter how many times you program it. California sun, especially in Beverly Hills where gates sit in full afternoon exposure, shortens keypad membrane life to roughly five to eight years before the buttons go soft and the codes start dropping.

OEM Linear parts are still the right call for most replacements. The tolerances on the receiver boards and the weather sealing on the keypads are hard to match honestly. There are decent aftermarket equivalents for simple items like remotes and photo-eye reflectors, and we’ll offer one when it makes sense and tell you exactly what you’re trading. But when the part lives outdoors and handles daily use, we lean OEM Linear every time. One more thing worth knowing: we’re an independent shop. We are not affiliated with Linear. We just fix their parts all day and keep the common ones on the truck.

And for context, we stock parts for LiftMaster, Mighty Mule, and Ghost Controls as well. So if it turns out the failure isn’t actually your Linear component but a Mighty Mule remote that drifted out of programming, we’ll find that on site instead of making a second trip.

Signs Your Linear Access Control Installation Is Failing

• Keypad lights up but the gate won’t move. The battery is fine and the buttons are good, but the transmitter portion of the board has given up. This is the single most common Linear keypad failure we see in Beverly Hills, especially on units that face west and get baked every afternoon.
• Gate opens fine from the wall button but not from remotes or the keypad. That points to the receiver, not the operator. If every remote fails at the same time, it’s almost never the remotes. It’s the receiver antenna or the receiver board itself.
• Remotes only work from three feet away. The antenna connection is corroded, or the receiver’s sensitivity has degraded. We see this a lot in coastal-adjacent neighborhoods like Beverly Hills where salt air gets into connectors even a few miles inland.
• Gate operates randomly at night or when no one is around. A failing receiver can pick up stray RF noise and trigger the open command. This one matters because your gate is your perimeter. When it opens itself at 2 a.m., you’ve got a security problem, not just an annoyance.
• You hear a click from the operator but nothing engages. The access signal is getting through, but the relay isn’t completing the circuit. Could be the access control unit or a limit switch downstream, but the click tells us the access path is at least partially alive.

Tell me what it’s doing and I’ll tell you what it needs, no guessing, no runaround. Most of these calls take about fifteen minutes to diagnose once we’re standing in front of the gate.

Replacement Cost & What’s Included

Here’s what we charge to replace Linear access control components in Beverly Hills:

• Linear keypad replacement: $240 to $380 installed, depending on whether we’re matching an AK-11 or a newer AE-KP series.
• Multi-Code receiver swap: $280 to $450 installed, including reprogramming your existing remotes to the new receiver.
• Full access control upgrade (keypad plus receiver plus two remotes): $480 to $580 installed, with everything programmed and tested before we leave.
• Remote replacement or addition: $45 to $75 per remote, programmed on site.

The range depends on two things: which Linear generation you have (older Multi-Code gear needs parts that are getting harder to source, so the prices sits a little higher), and whether the failed part damaged anything downstream, like wiring or the operator’s limit switch. You’ll get a written quote before any work starts, and the price we quote is the price you pay. If it’s over $200, the $40 off applies. If you’re a senior or veteran, it’s 10% off, same job. Every installation carries our 90-Day Done Right Promise in writing: if it’s not right, we come back and make it right, no charge and no argument.

DIY or Call Us?

Access control installation is low-voltage, so the immediate shock risk is minimal, but there’s a real danger hiding in the operator. Linear gates run on 110V at the operator, and the capacitor inside holds a charge even with power off. Poke the wrong terminal and you’ll feel it. We’d rather you not find that out the hard way. The other trap is programming: Linear receivers use a learn button sequence that varies by generation, and getting it half-right often leaves the gate working intermittently. An intermittent gate is worse than a dead one because you won’t know it failed until it strands someone outside at midnight.

Here’s the honest split. If your remote won’t program and the keypad is physically fine, that’s a five-minute fix we can often walk you through on the phone. If the keypad is cracked, the receiver is corroded, or the gate only works from one control point, that’s the job to hand off. We’ll bring the right part, install it, test it with every remote you own, and you’ll never wonder if the next button press is the one that quits. Call (559) 844-6989 and a live person answers, day or night.

FAQs