Ghost Controls Welding & Fabrication Nationwide | Gatewood Fence & Gate

Ghost Controls Welding & Fabrication: The Beverly Hills Owner’s Guide

We stock and install Ghost Controls-compatible welding and fabrication parts for gate openers and swing arms throughout Beverly Hills, with most replacements running $180 to $420 installed depending on the bracket, arm, or weld repair needed. We carry the common Ghost Controls hardware on the truck, so most repairs happen the same day we show up. The typical owner discovers the problem when the gate starts hesitating mid-swing, makes a grinding noise near the opener post, or the arm visibly droops where it meets the gate leaf.

Call (559) 844-6989

What you’re usually looking at is fatigue at the weld points or a bent pivot bracket. Ghost Controls builds a solid opener, but the fabrication points take real abuse in Beverly Hills, where gates swing hundreds of times a week and the coastal air works on bare metal. Hal Gatewood has opened plenty of Ghost Controls mechanisms in this neighborhood and found the same story: the opener still works fine, but the fabricated connection gave out. That’s a repair, not a replacement.

Key Takeaways

• Most Ghost Controls welding and fabrication repairs in Beverly Hills run $180 to $420 installed.
• We stock common Ghost Controls brackets, arms, and pivot hardware on the truck.
• Same-day repair is usually available when you call before early afternoon.
• We do the welding on-site, in your driveway, so the gate never leaves your property.
• Every fabrication job carries our 90-Day Done Right Promise in writing.

Which Ghost Controls Models This Applies To

Ghost Controls makes its openers under a few recognizable lines: the TSS1 and TDS2 series for single and dual swing gates, the SL series for slide gates, and the V-series for residential swing arms. The fabrication points that fail are consistent across these lines: the opener mounting bracket, the post pivot bracket, the clevis pin connection, and the arm extension where it bolts or welds to the gate leaf.

Here’s the compatibility gotcha we see in Beverly Hills all the time: the TSS1 uses a different arm tube diameter than the TDS2, and the mounting brackets are not interchangeable between them. If you order a generic bracket online thinking “a Ghost Controls bracket is a Ghost Controls bracket,” you’ll find out the hard way that the bolt pattern is off by a quarter inch. The same applies to the SL series slide gate hardware, which uses a heavier gauge steel than the swing arm parts. We match the part to your specific opener by the model number on the control board cover and by measuring the arm tube and bracket plate before anything gets ordered or welded.

On the OEM versus aftermarket question: Ghost Controls factory brackets are powder-coated and drilled to exact spec. Quality aftermarket equivalents exist, and we use them when they match or exceed the factory steel gauge. The difference is in the coating. In Beverly Hills, with the marine layer rolling in most mornings, we prefer a bracket with a proper zinc undercoat before the powder coat. Bare steel fabrications, even well-welded ones, start showing rust bloom within a year here.

We’re an independent gate service, not affiliated with Ghost Controls, and we also stock fabrication-compatible parts for LiftMaster, Mighty Mule, and DoorKing openers.

Signs Your Ghost Controls Welding & Fabrication Is Failing

• The gate stutters or jerks during travel. The opener arm has play in the clevis connection or the pivot bracket has started to oval out. The motor pushes, the slack takes up, and the gate lurches forward.
• You hear a metallic groan or creak from the post area. That’s metal rubbing on metal at a weld point that has cracked through enough to flex under load. It’s not a lubrication issue; it’s the arm telling you it’s fatiguing.
• The arm droops visibly where it meets the gate. The weld or the bracket has sagged, which changes the gate’s swing geometry. Left alone, it will tear the bracket clean off the post or the gate frame.
• You find rust-colored dust or flakes under the bracket. Fretting corrosion from a loose weld or misaligned bracket. In Beverly Hills, salt-laden air accelerates this once the coating is compromised.
• The gate stops short or won’t close all the way. The opener limits are set for the original arm geometry. A bent arm or shifted bracket changes the travel arc, and the gate lands wrong every cycle.

Replacement Cost & What’s Included

In Beverly Hills, a typical Ghost Controls fabrication repair lands between $180 and $420 installed. A simple bracket swap with new hardware runs at the lower end. A cracked weld repair on the gate leaf, where we grind out the old weld, re-weld, and reinforce the area, runs higher because of the labor involved. A full arm assembly replacement with new pivot hardware sits in the middle-to-upper range depending on the arm length and whether it’s a straight arm or an articulated one.

Every quote we give is the price you pay before we touch the gate. We write it down, you approve it, then we start. No discover-as-we-go pricing, no surprise upcharges at the door. The job includes grinding and prep, new hardware where needed, proper welding, and alignment of the gate after the repair so it swings true and the opener limits are set correctly. Every fabrication repair carries our 90-Day Done Right Promise in writing: if it’s not done right, we make it right. You also get $40 off any repair over $200, and no trip charge if you’re inside the county. Seniors and veterans get 10% off, always.

DIY or Call Us?

There are things worth checking yourself. Look at the bracket bolts: if they’re loose, that’s a wrench fix and we’ll tell you that over the phone for free. Check the arm for obvious visible cracks. Wipe off the grease and look at the weld lines. If you see a crack, don’t run the gate.

Here’s where DIY goes wrong: welding on a gate arm without removing the control board or disconnecting power is how you smoke a board. Ghost Controls control boards are sensitive to stray voltage from welding, and we’ve replaced boards in Beverly Hills that died exactly this way. Also, a gate arm is under tension from the gate’s weight and the opener’s holding torque. Welding on it without properly supporting the gate and releasing the manual release is dangerous. A gate that drops during a weld repair can break bones. This is not a scare tactic, it’s what we’ve seen. If the weld is cracked or the arm is bent, call us at (559) 844-6989. The estimate is free, and Hal will tell you plainly whether it’s a repair or a replacement before anything gets welded.

FAQs

Call Gatewood Fence & Gate in Beverly Hills

If your Ghost Controls gate is making noise, sagging, or acting up, tell me what it’s doing and I’ll tell you what it needs – no guessing, no runaround. We’ll come out, look at the fabrication points, and give you a written price before any work starts. The name is on the shop, and the shop is down the road. Call (559) 844-6989 for a free estimate, and you’ll get Hal or someone from his crew on the line, any hour, any day.

Written by Hal Gatewood, Owner, Gatewood Fence & Gate at Gatewood Fence & Gate, serving Beverly Hills and nearby areas.