BFT Gate Motor & Opener Nationwide | Gatewood Fence & Gate

BFT Gate Motor & Opener in Beverly Hills: What to Know First

Independent BFT gate motor and opener service in Beverly Hills is what we do. Call before 2 p.m. and in most cases Hal or one of his crew can be in the driveway within 48 hours to diagnose, and many repairs are completed same day. Pricing is quoted and agreed before any work starts, with no trip charge inside the county. If you own a BFT opener that’s clicking, grinding, or just stopped responding, call (559) 844-6989 and a live person picks up no voicemail, no call center.

Call (559) 844-6989

How BFT Products Fail - and How We Fix Them

• BFT Ares and Deimos series - capacitor burnout on hot days. Beverly Hills summers cook the capacitor inside these swing-gate motors. The gate moves a few inches, hums, then quits. We replace the capacitor with a higher-temperature-rated part. It’s a $90 to $140 fix, and we test the motor under load before we call it done.
• BFT Phobos slide operators - limit switch drift. The magnetic limit switches on Phobos N and A models can drift out of position after a couple years of daily cycles. The gate overshoots, reverses, or stops shy of fully open. We reset and recalibrate the limits, then verify the full travel. If the switch itself is failing, we swap it rather than forcing the motor to work around it.
• BFT Rigel 5 and Rigel 6 - control board relay failure. The relay that sends power to the motor wears out, especially on gates that cycle more than 50 times a day, like multi-home driveways off Sunset or Coldwater. The gate receives the remote signal but doesn’t move. We test the board, confirm the relay is the culprit, and replace the relay or board as needed. No board gets swapped unless it’s actually bad.
• BFT Thalia light-duty openers - stripped gearbox on overloaded gates. These are light residential motors. When someone hangs a 1,500-pound wrought-iron gate on a motor rated for half that, the gearbox eats itself. We see it in Beverly Hills on older estate gates that got upgraded over the years. The fix: match the gate to the motor, or the motor to the gate. Hal will tell you straight if the opener is undersized for the job.
• BFT photocells and safety edges - sun glare false stops. Direct afternoon sun on a south-facing driveway can blind infrared photocells. The gate reverses for no visible reason. We reposition, shield, or replace the cells as needed, and verify the safety edge wiring so the gate stops on actual contact, not on glare.

Our BFT Gate Motor & Opener Process

1. 1
   You call, we answer. Hal or his crew picks up 24/7. We ask what the gate is doing: clicking but not moving, moving halfway, beeping, dead quiet. That tells us a lot before we even load the truck.
2. 2
   On-site diagnosis. We test the motor, control board, limits, and safety devices. We open the unit up and look at what’s actually failed, not just what’s easy to replace.
3. 3
   Parts decision, made with you. We tell you which BFT parts need replacing, why, and whether OEM or quality aftermarket makes sense for your budget. We never swap parts that don’t need swapping.
4. 4
   The repair. We weld on site when needed. The gate stays in your driveway we don’t haul it off to some shop across town.
5. 5
   Test everything. Full open, full close, obstruction check, remote and keypad check. We run it through its paces with you watching.
6. 6
   Done right, in writing. Every job carries the 90-Day Done Right Promise. If it’s not done right, call and we make it right. That guarantee is stamped on the invoice, not buried in fine print.

What BFT Gate Motor & Opener Costs in Beverly Hills

Here’s what we typically charge for common BFT work in Beverly Hills:

• Diagnostic visit: $49 to $89, credited toward the repair if you proceed. No trip charge inside the county.
• Capacitor replacement (Ares, Deimos): $90 to $140
• Limit switch recalibration or replacement (Phobos): $120 to $220
• Control board repair or replacement (Rigel 5/6): $280 to $650, depending on the board and whether we can repair the existing one
• Gearbox rebuild on Thalia or similar: $180 to $400
• Full opener replacement, motor only: $850 to $1,600 installed
• Full swing or slide gate opener with controls: $1,800 to $3,800, depending on gate weight, length, and access control

We quote the price before any work starts and we honor it. Free estimates, and if you have a written estimate from another company, we’ll give you a free second opinion. Call (559) 844-6989 and you’ll know exactly what it costs before we turn a wrench.

Why Beverly Hills Homeowners Call Gatewood Fence & Gate for BFT Work

Hal Gatewood has been fixing gates in and around Beverly Hills since 2001. Back when he was driving a truck with a cracked windshield and a toolbox held shut with a bungee cord, he was already the guy neighbors called for stubborn gate problems. The name is on the shop, and the shop is down the road - that is the oldest accountability there is. We service BFT, but we also know LiftMaster, Mighty Mule, Ghost Controls, and DoorKing. When a BFT part is backordered and we can cross-reference a reliable aftermarket replacement, we’ll tell you. We don’t promise parts we can’t get. Every job carries the 90-Day Done Right Promise in writing. Call (559) 844-6989 - a live person answers every time.

FAQs