Ghost Controls Gate Installation Nationwide | Gatewood Fence & Gate

Ghost Controls Gate Installation in Beverly Hills: What to Know First

We install, wire, and program Ghost Controls gate openers on new and existing gates throughout Beverly Hills, and most jobs are done within a week of your call. You will get a written price before any work starts, matched to the gate you have, not a number pulled from a website. If you have been limping along with a Ghost Controls opener that half-works or a gate that was installed wrong the first time, call us at (559) 844-6989 and tell me what it’s doing. This page is for Beverly Hills homeowners who already own Ghost Controls equipment or are planning to buy it, and who want the installation done by someone who has actually opened one up and traced the wiring.

Call (559) 844-6989

Key Takeaways

• We install Ghost Controls openers on driveway gates, pedestrian gates, sliding gates, swing gates, double gates, and security gates in Beverly Hills.
• Every job gets a written price agreed before work starts. No surprises at the door.
• We are an independent Ghost Controls service provider, not a manufacturer-authorized dealer, which means we fix what is actually wrong instead of following a script.
• Most Ghost Controls installs take half a day to a full day depending on the gate type and power situation.
• We carry OEM Ghost Controls parts and quality aftermarket replacements, and we tell you which one makes sense for your gate before we order anything.

How Ghost Controls Products Fail - and How We Fix Them

Ghost Controls makes a solid opener for the price, but every brand has its weak spots. Here is what we see regularly on Beverly Hills gates and what we do about it.

• AXDP and AXXP series arm sag on swing gates. The actuator arm mounts to the gate post with a bracket that loosens over time, especially on gates facing Santa Monica Boulevard traffic vibration. The symptom is a gate that opens fine but creeps or drifts when it should hold position. We re-torque the bracket and install a reinforcement plate behind it, not just tighten and walk away.
• TSS1 and TDS1 limit switch drift on sliding gates. Ghost Controls sliding gate openers rely on magnetic limit switches that can shift out of alignment after a few hundred cycles. The gate stops short or over-travels and slams the stop post. We reset the limits and add a physical stop dampener so the magnet is not doing all the work.
• Draining control boards after Beverly Hills sprinkler exposure. The Ghost Controls control board is housed in a weather-resistant box, but drip irrigation set on a three-day cycle will find its way in. Ghost Controls boards are more sensitive to moisture than a LiftMaster board in our experience. We check the box gasket, relocate any sprinkler heads aimed at the opener, and if the board is fried, we replace it with OEM so you keep your warranty.
• Remote range complaints on long Beverly Hills driveways. The Ghost Controls remote receiver antenna is a short wire inside the control box. On gated estates with 150-foot plus driveway setbacks, that antenna can be too short to catch a remote from the street. We add a properly grounded external antenna extension, which Ghost Controls does not include in the box but works fine with their receiver.
• Battery backup neglect on the Ghost Controls EXP series. The EXP series controls a second gate or a pedestrian gate, and homeowners forget it has its own backup battery. After two years, the battery dies and the gate loses its mind every time power blinks. We test the battery during every install and swap it with a factory-spec replacement if it will not hold a charge.

Tell me what it’s doing and I’ll tell you what it needs - no guessing, no runaround.

Our Ghost Controls Gate Installation Process

Here is how a Ghost Controls install goes at Gatewood Fence & Gate, from the first call to the last bolt.

1. 1
   You call and talk to a live person. That person writes down what the gate is doing, what model opener you have, and what kind of gate it is. You get a window for us to come look, not a four-hour span that turns into rescheduling.
2. 2
   We show up, measure, and test. We check the gate’s weight, the hinge condition, the post plumb, and the power situation. On Beverly Hills hillside lots, we also check the slope of the driveway because a slight grade changes which opener arm length works.
3. 3
   We write the price. You get a number on paper before we touch a tool. That number includes the opener, mounting hardware, wiring, safety edges if needed, and cleanup.
4. 4
   We install and wire everything ourselves. Hal or one of his small crew handles the entire job. No subcontractor, no mystery person at the gate. On a Ghost Controls install, we pay extra attention to the control board placement and wire routing because those are the two things that fail early when someone rushes.
5. 5
   We test the full cycle and the safety reversal. The gate gets run through its open-close cycle at least ten times, with an obstruction test on both the leading and trailing edges. If it does not reverse properly, we adjust until it does or we fix the underlying cause.
6. 6
   We hand you the 90-Day Done Right Promise in writing. If anything we installed or touched fails within 90 days, one call brings us back. That is stamped on the invoice, not a verbal promise.

What Ghost Controls Gate Installation Costs in Beverly Hills

Ghost Controls openers are budget-friendly compared to a LiftMaster or DoorKing, but the installation labor is where Beverly Hills homeowners should watch the price. Here are honest ranges for the work we do most often.

What moves the price is the gate itself. A heavy iron gate needs a different arm and more mounting hardware than a light aluminum pedestrian gate. The power run matters too: if there is no outlet at the gate, we have to run conduit and a GFCI line, which adds labor. We quote the whole thing up front, and the number we quote is the number you pay. We do not charge a trip fee inside the county, so calling us to come look costs you nothing. Call (559) 844-6989 and we will give you a real price for your gate.

Why Beverly Hills Homeowners Call Gatewood Fence & Gate for Ghost Controls Work

Hal Gatewood started fixing gates in 2001, driving a truck with a cracked windshield and a toolbox held shut with a bungee cord. He went through the welding and fabrication program at Santa Monica College to get a real foundation under him, and he has been working on Beverly Hills gates ever since. His name is on the shop, his address is published, and his license number is available for anyone to look up. A gate sags in the hinge post, not in the middle, and that is where we start. We weld on site so your gate stays in your driveway: that means no hauling it off to a shop you have never seen. And if you own a LiftMaster, Mighty Mule, or DoorKing, we service those too, which means we are not trying to sell you a brand, we are trying to make your gate work.

FAQs

Call Gatewood Fence & Gate for Your Ghost Controls Installation in Beverly Hills

If you own a Ghost Controls opener and need it installed right, or you have one that was installed wrong and you are tired of fighting it, call Hal at Gatewood Fence & Gate. A live person answers around the clock, you will get a written price before work starts, and the 90-Day Done Right Promise backs every job. No trip charge inside the county. Free second opinion on any written estimate. Call (559) 844-6989 today and tell me what your gate is doing.

Written by Hal Gatewood, Owner, Gatewood Fence & Gate at Gatewood Fence & Gate, serving Beverly Hills and nearby areas.