Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterViking Gate Installation in Beverly Hills: What to Know First
Viking gate installation in Beverly Hills runs between $2,400 and $7,800 for most residential jobs, depending on whether you’re replacing a single swing gate or setting up a full double driveway system with a new operator. We typically complete a standard Viking installation in one to two days once parts are on hand, and every job is quoted and agreed before any work starts. If you own a Viking gate or operator that needs proper installation and you want it done by someone who will answer the phone when you call afterward, you’re in the right place. We’re Gatewood Fence & Gate, an independent Viking service provider, and Hal Gatewood has been working on gates in and around Beverly Hills since 2001. Call (559) 844-6989 and you’ll get a live person, day or night.
How Viking Products Fail - and How We Fix Them
Viking gates are built differently than most residential brands, and that means their failure patterns are different too. Here’s what we actually see on Viking jobs in Beverly Hills.
- Viking R-6 and S-2 swing operators losing limit settings after power dips. Beverly Hills sees enough brownouts and brief outages that Viking control boards sometimes forget their open and close limits. The gate then slams into the mechanical stops or stops three feet short of closed. We reset the limits properly, verify the battery backup if the system has one, and often add a small surge suppressor at the board so the settings stick.
- Viking LA-4 and LA-8 slide gate wheels eating into the track on sloped driveways. A lot of Beverly Hills properties have graded entries, and when a Viking slide gate is installed even slightly off-level, the wheel assembly takes the brunt of it. You’ll hear a grinding sound and see metal shavings under the gate. We level the track, weld new wheel brackets if needed, and set the gate so it carries its weight evenly instead of chewing through parts.
- OEM Viking photo-eye alignment issues on double gates. Viking’s safety eyes are particular about alignment, especially on wide double gates where one side settles a fraction of an inch. The gate will start, then immediately reverse and sit there half-open. We align and shim both posts so the beam stays clean, then cycle the gate a dozen times to confirm it holds.
- Viking control board failures from ants and moisture. This is a real thing in Beverly Hills. Ants get into Viking control boxes, short out contacts, and the gate goes dead or erratic. We clean the board, repair repairable contacts, and seal entry points. If the board is beyond saving, we recommend quality aftermarket boards that match Viking’s voltage and wiring, which keeps your warranty intact.
- Chain-drive Viking operators with stretched chains on heavy gates. When a Viking chain stretches past adjustment, the gate jerks and bangs. The fix isn’t always a new operator. We shorten or replace the chain, check the sprockets for wear, and re-set the torque limits so the gate moves smoothly instead of lurching. That’s the repair-first approach: fix what’s actually worn, not what’s easiest to sell.
Our Viking Gate Installation Process
Here’s how a Viking gate installation goes with us, start to finish.
- 1
You call, a person answers. Not a voicemail. We talk through what Viking equipment you have, what it’s doing or not doing, and set a time that works. No trip charge inside the county.
- 2
Hal or his crew shows up and opens the gate up. We look at the operator, the hinges, the posts, the wiring, the track if there is one. We find the root problem before touching a wrench. Sometimes the operator is fine and the post is the issue. Fixing the operator without fixing the post means you’ll fix it twice.
- 3
You get a written price before anything is ordered. We decide together whether OEM Viking parts make sense or whether a quality aftermarket part does the same job for less. If your Viking unit is under warranty, we’ll tell you and we’ll work within the warranty rules so you don’t forfeit coverage.
- 4
The work happens at your property. We weld on site, in your driveway. Your gate stays in your driveway, not hauled off to some shop. New posts are set and squared, the gate is hung and balanced, the operator is mounted and wired, safety edges and photo eyes are installed and tested.
- 5
We test it until it’s boring. We cycle the gate through open and close at least a dozen times, check the force settings, verify the auto-reverse, and watch it in the rain if rain is coming. Boring is the goal.
- 6
You get the 90-Day Done Right Promise in writing. If something isn’t right, one call brings us back. No runaround, no arguing. Our name is on the invoice and the shop is down the road.
What Viking Gate Installation Costs in Beverly Hills
Here are straight numbers for the Viking jobs we do most often in Beverly Hills. These are installed prices including labor, standard mounting hardware, and a written guarantee.
- Single swing gate with a new Viking operator: $2,400 to $3,900
- Double swing gate with new Viking operators on both sides: $4,200 to $6,500
- Pedestrian gate with Viking keypad entry: $1,900 to $3,200
- Sliding gate with Viking operator and new track: $3,500 to $5,800
- Full replacement: new gate, posts, operator, and access control: $5,500 to $7,800
What moves the price is gate size, whether we’re digging and setting new posts or using existing ones, access control features, and whether existing wiring is salvageable. Beverly Hills properties with longer runs from the house to the gate can add to the labor. Every quote is fixed before work starts, and every job qualifies for a free estimate. We also have a free second opinion on any written estimate, $40 off any repair over $200, and a permanent 10% discount for seniors and veterans. Call (559) 844-6989 and we’ll get you a number.
Why Beverly Hills Homeowners Call Gatewood Fence & Gate for Viking Work
Hal Gatewood has been fixing gates around Beverly Hills since 2001, when his truck still had a cracked windshield and a toolbox held shut with a bungee cord. He grew up not far from Roxbury Park, went through the welding and fabrication program at Santa Monica College, and never left the area because Beverly Hills kept him busy enough. The name is on the shop, the address is published, and the license number is right there for anyone to look up. That’s the oldest accountability there is.
When we work on a Viking gate, we know what we’re looking at. Hal gets genuinely irritated when he opens up a gate mechanism and finds somebody else’s half-done work staring back at him, and that’s what drives the repair-first approach. Show us a gate closing on its own and we’ll show you where it’s failing. We also service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so if your property has mixed brands or you’re switching away from one, we can handle it without bringing in a second company. Every job is covered by the 90-Day Done Right Promise, stamped in writing. One call and we come back.
FAQs
Yes. You bought the gate, we’ll install it. We install Viking equipment homeowners have purchased, and we’ll inspect it before we start to make sure it’s complete and road-worthy. If something’s missing or damaged, we’ll tell you before the work starts so there are no surprises. Call (559) 844-6989 and we’ll schedule the install.
No. We are an independent Viking service provider, not affiliated with or authorized by the manufacturer. That said, we work on Viking gates and operators regularly in Beverly Hills and we know the model lines, the wiring, and the weak points. Being independent means we can recommend aftermarket parts when they’re genuinely better or cheaper without a manufacturer quota hanging over our heads.
It depends on which components are under warranty and what we’re replacing. We keep installation practices warranty-safe, meaning we match voltage, avoid splices where Viking’s specs call for clean runs, and we’ll tell you honestly if a repair is warranty-eligible before starting. We won’t patch over a problem in a way that quietly kills your coverage. Call us at (559) 844-6989 and we’ll walk you through it.
Most standard Viking gate installations are completed within one to two days once parts are on hand. If you already have the gate and operator, we can often start within a few days. If we need to order Viking-specific parts, that timing depends on the supply chain, and we’ll give you a straight answer on lead times before you commit to anything. We don’t promise same-day on installations because the work is measured, ordered, and scheduled properly. Call (559) 844-6989 for an honest timeframe.
It depends on the post, the hinges, and the operator, in that order. If the hinges are still solid and the post hasn’t moved, we’ll usually repair. A sagging gate is a hinge post issue, not a gate panel issue, and fixing the panel without the post means you’ll fix it twice. We’ll tell you what we’d do if it were our gate, and the answer isn’t always the most expensive one. Call (559) 844-6989 for a free estimate and we’ll give you a straight answer.
Tell me what it’s doing and I’ll tell you what it needs, no guessing, no runaround. Call (559) 844-6989 and talk to a live person. We’ll set a time, show up in the window we promised, and hand you a written price before any work starts. If you’d rather look us in the eye first, drive to the shop. The address is on our site, and Hal’s name is on the door.
Written by Hal Gatewood, Owner, Gatewood Fence & Gate at Gatewood Fence & Gate, serving Beverly Hills and nearby areas.