Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterLinear Gate Repair in Beverly Hills: What to Know First
Independent Linear gate repair in Beverly Hills typically runs $180 to $480 for most operator and mechanical fixes, and we can usually get to you within one business day. The final price depends on which Linear model you have and whether it’s a board, a gear, or a hinge post that gave out. We quote the number before we touch a tool, and the figure we quote is the figure on the invoice. If you’ve got a Linear gate that won’t open, won’t stay open, or sounds like it’s chewing gravel, call us at (559) 844-6989. Hal Gatewood has been fixing gates in Beverly Hills since 2001, and we’re not hard to find when something needs a second look.
How Linear Products Fail - and How We Fix Them
Linear operators show up all over Beverly Hills, from the flat driveways off Olympic to the gated side entries near Roxbury Park. We see the same five failure patterns year after year.
- Linear M-series and LCO-series drive arm stripping or popping free. The M-series (and the LCO line that followed it) uses a screw-drive arm that threads into a coupler at the operator. When the gate hits an obstruction or a hinge post settles, the brass insert in that coupler strips out. The arm still spins but the gate doesn’t move. We replace the coupler insert rather than selling you a whole new operator. That’s a $60 fix versus what some companies quote.
- APeX and LRA-series limit switch drift. The APeX and LRA boards rely on a magnetic limit sensor that reads a disc on the drive shaft. When that disc picks up metallic dust from Santa Ana wind days, the gate over-travels past its stop and slams the post. We clean and reseat the sensor and reset limits. If the board itself is fried, we price a replacement board honestly, because a board is often less than a third the cost of a full operator.
- Linear M3 and LSO photo eye feedback failing with no visible damage. Here’s a nuance you won’t find on Linear’s site: those photo eyes run a continuous beam, and the housings collect condensation at night along Beverly Hills’ north-facing walls. Water sits in the lens cup, the beam scatters, and the gate refuses to close even though the eyes look fine. We drill a small drain and reseal the lens. Linear doesn’t show that drill point in any schematic.
- Worm gear grease breaking down in direct sun. Beverly Hills properties on the flats get full afternoon exposure. The grease inside a Linear operator turns to paste over time because the aluminum housing holds heat. The motor then strains, draws high amps, and trips the thermal breaker. We open the unit, clean the old paste out, repack it, and the operator quiets down immediately. This is maintenance, not replacement.
- Hinge post settlement on the heavier Linear swing setups. Big driveway gates on Linear LRA operators are often steel-frame with stucco cladding, and they’re heavy. When the post shifts even a quarter inch, the drive arm angle changes and everything up the chain wears faster. We weld a reinforcement plate at the post base and realign the arm. This is the repair that keeps the new parts from burning out in a year.
Our Linear Gate Repair Process
We work on the gate where it stands. We don’t haul it off to a shop and we don’t make you wait a week for a decision. Here’s how a typical Linear job goes at a Beverly Hills home:
- 1
You call (559) 844-6989. A live person answers, 24/7. You describe the symptom. We tell you who’s coming and when.
- 2
We show up and diagnose. We pull the cover on the operator, check the board for codes, run the gate manually, and test the safety edges. We find the root problem, not the loudest symptom.
- 3
We give you the number. Before any work starts, you get a written price for parts and labor. No “we’ll see how it goes.” No surprise line items.
- 4
We repair on site. If it needs a board, a gear, a weld, or a hinge repair, we handle it in your driveway. We carry Linear OEM parts for common failures and quality aftermarket replacements when they’re the smarter call.
- 5
We test the gate through a full cycle. Open, close, obstruction reversal, photo eye interruption. If it doesn’t work the way it should, we’re not done.
- 6
You get the 90-Day Done Right Promise. Stamped in writing on the invoice. If something we touched fails within 90 days, one call brings Hal back at no charge.
What Linear Gate Repair Costs in Beverly Hills
Every gate is different, but here are honest ranges for the Linear jobs we see most often:
| Linear Repair Scenario | Typical Cost Range |
|---|---|
| M-series/LCO coupler insert replacement | $60 - $120 |
| APeX or LRA limit switch reset and reseat | $90 - $180 |
| Photo eye alignment, drain, and reseal | $75 - $150 |
| Worm gear degrease and repack | $110 - $200 |
| Replacement control board (OEM) | $180 - $400 installed |
| Hinge post weld repair and gate realignment | $250 - $480 |
What moves the price: whether the gate is swing or slide, how heavy the gate is, whether we’re cutting and welding or just swapping a part, and whether the failure damaged anything downstream. We give free estimates on Linear repair work. We also give $40 off any repair over $200, and seniors and veterans get 10% off every job, every time. The price you hear is the price you pay.
Why Beverly Hills Homeowners Call Gatewood Fence & Gate for Linear Work
Hal Gatewood’s name is on the shop. He’s been at this since 2001, and he grew up not far from Roxbury Park, so a Beverly Hills gate is not an address to him - it’s a neighbor. The person who shows up is the person who answers the phone. We weld on site, which means your gate never leaves your driveway, and we fix what can be fixed rather than quoting you a new operator because it’s easier for us. If you’ve got a Linear and something has gone wrong, you get the straight answer. And if you’ve ever been burned by a company that quoted one price on the phone and another at the door, you’ll notice the difference within the first ten minutes. We also service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so if you have a mixed setup, one call covers it all.
Tell me what it’s doing and I’ll tell you what it needs - no guessing, no runaround.
FAQs
We’re an independent Linear service provider, not a factory-authorized warranty station, so any warranty claim goes through Linear or your original installer. That said, most Linear operators in Beverly Hills fail years after the warranty expired, and our 90-Day Done Right Promise covers the labor and the parts we install from the day we finish. If it’s not done right, we make it right - that’s in writing.
We stock Linear OEM parts for the M-series, LCO, APeX, LRA, and LSO lines, and for older units we work through a network of authorized parts suppliers that still carry boards, gears, and arms for discontinued models. When an OEM part is backordered for weeks and a quality aftermarket part exists with the same specs, we tell you both options and let you decide. We never hide the fact that a part is aftermarket.
For a gate stuck open or a gate that won’t move, we prioritize emergency calls and can usually be there the same day in Beverly Hills. For a noisy operator or a slow-opener, we typically schedule within one business day. Call (559) 844-6989 and tell us what the gate is doing - a live person answers and we’ll tell you how soon we can be there.
If the housing is intact and the board hasn’t burned through, repair almost always makes sense - a new Linear operator runs $700 to $1,200 installed, and most failures are a $60 to $400 part. We’ll tell you straight if a repair would be throwing good money after bad, but that’s rare. We’ve rebuilt units that were 12 years old and still running fine a year later because the mechanical bones were solid.
Sun is the bigger enemy than rain here. Beverly Hills gets long, warm afternoons all year, and that heat cycles the grease, the board capacitors, and the plastic coupler inserts. Units on full south-facing exposure age faster than shaded ones. If your operator sits in direct sun all afternoon, ask us about a simple vented cover when we’re out - it’s cheaper than replacing a warped board.
Written by Hal Gatewood, Owner, Gatewood Fence & Gate at Gatewood Fence & Gate, serving Beverly Hills and nearby areas.